just shaped this up
what you think?
Nice shape, I m eggstatic!
Im eggcited!!.
Nice ken!
thanks guys!
Im hopeing for reverbs blessing
Needs a bolt…
i want it! Hahah!
Ken:
Put a bottom bevel in the nose. It will make it look
a lot thinner than it actually is. Learned this trick from
Rich H. Otherwise, great shape. What are you doing
as far as bottom contours go & fins? How much V in the
tail? keep on rockin…
BKB
First you go after those poor Lightning Bolt fellows and now oncoming to Easter you're pulling out Eggs?!?!?! You better start watching your back man. If you begin to notice pellets on the ground, don't think they're Jujubees......Look Out!!
[quote="$1"]
just shaped this up
what you think?
[/quote]
The other night I had this dream / nightmare....A big K was out in my shop stealing all my prototype designs...Mike D shows up in a Le Mans race car and chases away the bad guy......and then I woke up in a cold sweat....
....and today Ken posts up one of my designs....ha,ha...
I love the board Ken....
For small eggs I'm doing 50/50 rails with rolled bottom. Smooth and simple.......
[quote="$1"] Ken: Put a bottom bevel in the nose. It will make it look a lot thinner than it actually is. Learned this trick from Rich H. Otherwise, great shape. What are you doing as far as bottom contours go & fins? How much V in the tail? keep on rockin.... BKB [/quote]
I like the bevel idea,,, dont know what I was thinking,,,,Ive beveled longboards,,, duh
its 2 1/4 thick and rails are down about 70/30
its concaved in the middle about 3/16 or so, gradualy changing to 1/4" V before the fins, with concaves through the fins (thruster)
[quote="$1"]
First you go after those poor Lightning Bolt fellows and now oncoming to Easter you're pulling out Eggs?!?!?! You better start watching your back man. If you begin to notice pellets on the ground, don't think they're Jujubees......Look Out!!
[/quote]
!!!! Oh Shit !!!!
I wonder if the easter bunny has cleaners
[quote="$1"]
[quote="$1"]
just shaped this up
what you think?
[/quote]
The other night I had this dream / nightmare....A big K was out in my shop stealing all my prototype designs...Mike D shows up in a Le Mans race car and chases away the bad guy......and then I woke up in a cold sweat....
....and today Ken posts up one of my designs....ha,ha...
I love the board Ken....
For small eggs I'm doing 50/50 rails with rolled bottom. Smooth and simple.......
[/quote]
Yes! Yes! I can enter your mind and steel all your Rayish thoughts,
Going by reverbs last few post's in other threads, it won't be positive.
But i love it, it'll go sweet. Im doing an egg ( very bloody slowly ) at the moment, and due to the thickness of the blank, im going upturned rails in the nose ( as much as i can, possibly some belly ), then 70/30 in the middle, to soft down in the tail. Im gunna stick with flat bottom though.
Tint??????
…hello Kensurf,
well, as you know Im very picky, so take these words in a good way.
First I only rely on the previous pictures to comment on the work.
Looking the photos I see kind of not so curved part (on the middle) on the right side of the outline compared to the left side.
then about 3-4 inches from tail that right side outline looks a bit different too
May be are the shadows, etc so I repeat, I m not telling that is not right I m commenting on what I see on the pictures.
The lines from tail looking ok.
In the view from nose there s a not so pure line passing middle of the rail to tail
I prefer to thin or tapered out tail and nose.
I prefer to rolled a bit the nose entry
I distribute the foil a bit different
Possibly you can check again those parts
Ot better ask for S Frye ´ opinion!
Eggcellent, Ken.
[quote="$1"]
...hello Kensurf,
well, as you know Im very picky, so take these words in a good way.
First I only rely on the previous pictures to comment on the work.
Looking the photos I see kind of not so curved part (on the middle) on the right side of the outline compared to the left side.
then about 3-4 inches from tail that right side outline looks a bit different too
May be are the shadows, etc so I repeat, I m not telling that is not right I m commenting on what I see on the pictures.
The lines from tail looking ok.
In the view from nose there s a not so pure line passing middle of the rail to tail
I prefer to thin or tapered out tail and nose.
I prefer to rolled a bit the nose entry
I distribute the foil a bit different
Possibly you can check again those parts
Ot better ask for S Frye ´ opinion!
[/quote]
hey reverb
thanks for your input
I think the out line is even , the background in the pics is not the best for pics and will throw you off
but I will check it out.
this board is thin and tapered ,,the tail is less than 3/4 maybe 5/8 thick
nose is thin also
pics are strainge,,,, I think I had the flash on
thanks Balsa
hey beerfan
Im thinking of opaque yellow bottom and light yellow tint deck
Howzit Ken, Easter Bunny=Cleaners.
Who do you think the Boogeyman is?
Better lock up your Egg Basket.