I was wondering if you had worked up a matrix for a 7’ thruster over 3" thick or anything else that’s similar. I like your thinking in terms of tail width and design…Thank you!!!
I was wondering if you had worked up a matrix for a 7’ thruster over > 3" thick or anything else that’s similar. I like your thinking in > terms of tail width and design…Thank you!!! Dood, You’re taking some risk turning me loose on a thruster. You’ might have to surf the kinds of boards that I like. (: o) Here’s my best shot. It’s 7-0 x 14.8"t x 21" x 13"n. The wide point is 3" forward of center and the stern is 4" square. Rocker progression is limited. Tail rocker is 3% of board length and nose rocker tends to 30 degrees from center tangent. Foam is 3" thick with moderate deck crown to moderately full rails. Rail line is .8" above bottom foam and has .7" tuck. I made the 3" forward width offset to equalize the wide center and tail widths. The board is set up for heavier surfers in summer surf (N hemi). Keep the V to a minimum. Good luck. Length , Outline , Rocker 0 , 0.00 , 2.50 0 , 2.00 , 2.50 0.5 , 2.54 , 2.42 1 , 2.98 , 2.34 2 , 3.69 , 2.19 3 , 4.28 , 2.05 4 , 4.78 , 1.92 5 , 5.22 , 1.79 6 , 5.61 , 1.68 7 , 5.97 , 1.57 8 , 6.30 , 1.46 9 , 6.61 , 1.36 10 , 6.89 , 1.27 11 , 7.15 , 1.18 12 , 7.40 , 1.10 13 , 7.63 , 1.02 14 , 7.85 , 0.94 15 , 8.05 , 0.87 16 , 8.24 , 0.80 17 , 8.42 , 0.74 18 , 8.59 , 0.67 19 , 8.75 , 0.62 20 , 8.90 , 0.56 21 , 9.04 , 0.51 22 , 9.18 , 0.46 23 , 9.30 , 0.41 24 , 9.42 , 0.37 25 , 9.53 , 0.33 26 , 9.63 , 0.29 27 , 9.73 , 0.25 28 , 9.82 , 0.22 29 , 9.90 , 0.19 30 , 9.98 , 0.16 31 , 10.05 , 0.13 32 , 10.12 , 0.11 33 , 10.18 , 0.09 34 , 10.23 , 0.07 35 , 10.28 , 0.05 36 , 10.32 , 0.04 37 , 10.36 , 0.03 38 , 10.40 , 0.02 39 , 10.43 , 0.01 40 , 10.45 , 0.00 41 , 10.47 , 0.00 42 , 10.48 , 0.00 43 , 10.49 , 0.00 44 , 10.50 , 0.01 45 , 10.50 , 0.01 46 , 10.49 , 0.02 47 , 10.46 , 0.03 48 , 10.42 , 0.05 49 , 10.37 , 0.06 50 , 10.31 , 0.08 51 , 10.24 , 0.10 52 , 10.16 , 0.12 53 , 10.07 , 0.15 54 , 9.98 , 0.18 55 , 9.87 , 0.21 56 , 9.75 , 0.24 57 , 9.63 , 0.28 58 , 9.49 , 0.32 59 , 9.35 , 0.37 60 , 9.20 , 0.41 61 , 9.04 , 0.46 62 , 8.86 , 0.51 63 , 8.68 , 0.57 64 , 8.49 , 0.63 65 , 8.29 , 0.70 66 , 8.07 , 0.77 67 , 7.84 , 0.84 68 , 7.60 , 0.92 69 , 7.35 , 1.00 70 , 7.08 , 1.09 71 , 6.80 , 1.18 72 , 6.50 , 1.28 73 , 6.18 , 1.39 74 , 5.84 , 1.51 75 , 5.48 , 1.63 76 , 5.10 , 1.77 77 , 4.68 , 1.91 78 , 4.23 , 2.07 79 , 3.74 , 2.25 80 , 3.20 , 2.45 81 , 2.59 , 2.68 82 , 1.90 , 2.95 83 , 1.07 , 3.29 83.5 , 0.58 , 3.51 84 , 0.00 , 3.80 Rail: Width , Deck , Bottom 0 , 2.20 , -0.80 1 , 2.20 , -0.80 2 , 2.20 , -0.80 3 , 2.20 , -0.80 4 , 2.19 , -0.80 5 , 2.17 , -0.80 6 , 2.13 , -0.80 6.5 , 2.10 , -0.80 7.0 , 2.05 , -0.80 7.5 , 1.98 , -0.80 8.5 , 1.78 , -0.80 9.0 , 1.61 , -0.80 9.5 , 1.38 , -0.80 9.6 , 1.32 , -0.80 9.7 , 1.26 , -0.80 9.8 , 1.19 , -0.80 9.9 , 1.11 , -0.79 10 , 1.02 , -0.77 10.1 , 0.92 , -0.72 10.2 , 0.81 , -0.66 10.3 , 0.67 , -0.56 10.40 , 0.48 , -0.41 10.45 , 0.34 , -0.30 10.50 , 0.00 , -0.00
Many Thanks, Mr. Noodle…I also pulled your 6’6" fish matrix out of the archives…great stuff for a hacker like me…