Noodle; can you please help me with some numbers for a 10’6"? I’m thinking 18.5"nose,23.5 wide point at center,14.5" tail with 5" squash. Thanks for your time and thank you swaylock for a great site!
for a 10’6 noserider, i’d so something more like 19" nose, 23.5wide point, a 16" tail, and a 7" squash -steve
Noodle; can you please help me with some numbers for a 10’6"? I’m > thinking 18.5"nose,23.5 wide point at center,14.5" tail with > 5" squash. Thanks for your time and thank you swaylock for a great > site! Yes. I’m on it… with some other stuff. Check back in a couple of hours.
Noodle; can you please help me with some numbers for a 10’6"? I’m > thinking 18.5"nose,23.5 wide point at center,14.5" tail with > 5" squash. Thanks for your time and thank you swaylock for a great > site! Here’s your shape. I included rocker with a little tail progression, so you can add some turning V. The nose has just a tad of sharpness. I can’t see the thread below, but somebody brought up how 1’ widths are measured a smaller percentage up the board for bigger boards. Steve has a point about tail width on such a big board, but I would tone it down some from his. Nose width is a compromise any way you look at it. Wider for noseriding, narrower for turning. To me, 18.5 is a good compromise for a board so long. To keep this organized, I’ll post your numbers here, Steve’s numbers under his post, and my compromise under my post. All have 3" forward width offset, so the noses and tails are interchangeable from the wide point, 66" forward from the stern. Hereis the outline with your numbers: x , y , Rocker 0.0 , 0.00 , 3.90 0.0 , 2.50 , 3.90 0.5 , 3.02 , 3.81 1.0 , 3.41 , 3.72 2.0 , 4.03 , 3.55 3.0 , 4.53 , 3.39 4.0 , 4.96 , 3.23 5.0 , 5.33 , 3.09 6.0 , 5.67 , 2.95 7.0 , 5.98 , 2.82 8.0 , 6.27 , 2.69 9.0 , 6.54 , 2.57 10.0 , 6.79 , 2.45 11.0 , 7.03 , 2.34 12.0 , 7.25 , 2.23 13.0 , 7.46 , 2.13 14.0 , 7.66 , 2.03 15.0 , 7.86 , 1.94 16.0 , 8.04 , 1.84 17.0 , 8.21 , 1.75 18.0 , 8.38 , 1.67 19.0 , 8.54 , 1.59 20.0 , 8.70 , 1.51 21.0 , 8.85 , 1.43 22.0 , 8.99 , 1.35 23.0 , 9.13 , 1.28 24.0 , 9.26 , 1.21 25.0 , 9.39 , 1.15 26.0 , 9.51 , 1.08 27.0 , 9.63 , 1.02 28.0 , 9.74 , 0.96 29.0 , 9.85 , 0.90 30.0 , 9.96 , 0.84 31.0 , 10.06 , 0.79 32.0 , 10.16 , 0.74 33.0 , 10.26 , 0.69 34.0 , 10.35 , 0.64 35.0 , 10.44 , 0.60 36.0 , 10.52 , 0.55 37.0 , 10.60 , 0.51 38.0 , 10.68 , 0.47 39.0 , 10.75 , 0.43 40.0 , 10.83 , 0.40 41.0 , 10.90 , 0.36 42.0 , 10.96 , 0.33 43.0 , 11.03 , 0.30 44.0 , 11.09 , 0.27 45.0 , 11.14 , 0.24 46.0 , 11.20 , 0.21 47.0 , 11.25 , 0.19 48.0 , 11.30 , 0.16 49.0 , 11.35 , 0.14 50.0 , 11.39 , 0.12 51.0 , 11.43 , 0.10 52.0 , 11.47 , 0.09 53.0 , 11.51 , 0.07 54.0 , 11.54 , 0.06 55.0 , 11.58 , 0.04 56.0 , 11.61 , 0.03 57.0 , 11.63 , 0.02 58.0 , 11.66 , 0.02 59.0 , 11.68 , 0.01 60.0 , 11.70 , 0.00 61.0 , 11.71 , 0.00 62.0 , 11.72 , 0.00 63.0 , 11.74 , 0.00 64.0 , 11.74 , 0.00 65.0 , 11.75 , 0.00 66.0 , 11.75 , 0.01 67.0 , 11.75 , 0.02 68.0 , 11.75 , 0.02 69.0 , 11.75 , 0.03 70.0 , 11.75 , 0.04 71.0 , 11.75 , 0.05 72.0 , 11.75 , 0.07 73.0 , 11.75 , 0.08 74.0 , 11.75 , 0.10 75.0 , 11.75 , 0.12 76.0 , 11.75 , 0.14 77.0 , 11.75 , 0.16 78.0 , 11.75 , 0.19 79.0 , 11.74 , 0.21 80.0 , 11.74 , 0.24 81.0 , 11.74 , 0.27 82.0 , 11.73 , 0.30 83.0 , 11.73 , 0.33 84.0 , 11.72 , 0.37 85.0 , 11.71 , 0.40 86.0 , 11.71 , 0.44 87.0 , 11.70 , 0.48 88.0 , 11.68 , 0.52 89.0 , 11.67 , 0.57 90.0 , 11.65 , 0.61 91.0 , 11.63 , 0.66 92.0 , 11.61 , 0.71 93.0 , 11.58 , 0.77 94.0 , 11.55 , 0.82 95.0 , 11.51 , 0.88 96.0 , 11.47 , 0.94 97.0 , 11.43 , 1.00 98.0 , 11.38 , 1.07 99.0 , 11.33 , 1.13 100.0 , 11.26 , 1.21 101.0 , 11.19 , 1.28 102.0 , 11.12 , 1.36 103.0 , 11.03 , 1.43 104.0 , 10.94 , 1.52 105.0 , 10.83 , 1.60 106.0 , 10.72 , 1.69 107.0 , 10.59 , 1.79 108.0 , 10.45 , 1.89 109.0 , 10.29 , 1.99 110.0 , 10.12 , 2.10 111.0 , 9.94 , 2.21 112.0 , 9.73 , 2.32 113.0 , 9.50 , 2.45 114.0 , 9.25 , 2.58 115.0 , 8.97 , 2.71 116.0 , 8.66 , 2.85 117.0 , 8.32 , 3.01 118.0 , 7.94 , 3.17 119.0 , 7.51 , 3.34 120.0 , 7.03 , 3.52 121.0 , 6.48 , 3.72 122.0 , 5.84 , 3.94 123.0 , 5.07 , 4.17 124.0 , 4.13 , 4.44 125.0 , 2.84 , 4.74 126.0 , 0.00 , 5.10
Yes. I’m on it… with some other stuff. Check back in a couple of hours. Here’s board with 14.8" tail and all your other numbers, including 5" stern. I think the curve looks slightly better and would help catch more waves: x , y , Rocker 0.0 , 0.00 , 3.90 0.0 , 2.50 , 3.90 0.5 , 3.04 , 3.81 1.0 , 3.46 , 3.72 2.0 , 4.10 , 3.55 3.0 , 4.61 , 3.39 4.0 , 5.05 , 3.23 5.0 , 5.44 , 3.09 6.0 , 5.79 , 2.95 7.0 , 6.11 , 2.82 8.0 , 6.40 , 2.69 9.0 , 6.68 , 2.57 10.0 , 6.93 , 2.45 11.0 , 7.17 , 2.34 12.0 , 7.40 , 2.23 13.0 , 7.61 , 2.13 14.0 , 7.82 , 2.03 15.0 , 8.01 , 1.94 16.0 , 8.20 , 1.84 17.0 , 8.37 , 1.75 18.0 , 8.54 , 1.67 19.0 , 8.70 , 1.59 20.0 , 8.86 , 1.51 21.0 , 9.01 , 1.43 22.0 , 9.15 , 1.35 23.0 , 9.28 , 1.28 24.0 , 9.42 , 1.21 25.0 , 9.54 , 1.15 26.0 , 9.66 , 1.08 27.0 , 9.78 , 1.02 28.0 , 9.89 , 0.96 29.0 , 10.00 , 0.90 30.0 , 10.10 , 0.84 31.0 , 10.20 , 0.79 32.0 , 10.30 , 0.74 33.0 , 10.39 , 0.69 34.0 , 10.48 , 0.64 35.0 , 10.56 , 0.60 36.0 , 10.64 , 0.55 37.0 , 10.72 , 0.51 38.0 , 10.79 , 0.47 39.0 , 10.86 , 0.43 40.0 , 10.93 , 0.40 41.0 , 11.00 , 0.36 42.0 , 11.06 , 0.33 43.0 , 11.12 , 0.30 44.0 , 11.17 , 0.27 45.0 , 11.23 , 0.24 46.0 , 11.28 , 0.21 47.0 , 11.32 , 0.19 48.0 , 11.37 , 0.16 49.0 , 11.41 , 0.14 50.0 , 11.45 , 0.12 51.0 , 11.49 , 0.10 52.0 , 11.52 , 0.09 53.0 , 11.55 , 0.07 54.0 , 11.58 , 0.06 55.0 , 11.61 , 0.04 56.0 , 11.64 , 0.03 57.0 , 11.66 , 0.02 58.0 , 11.68 , 0.02 59.0 , 11.69 , 0.01 60.0 , 11.71 , 0.00 61.0 , 11.72 , 0.00 62.0 , 11.73 , 0.00 63.0 , 11.74 , 0.00 64.0 , 11.75 , 0.00 65.0 , 11.75 , 0.00 66.0 , 11.75 , 0.01 67.0 , 11.75 , 0.02 68.0 , 11.75 , 0.02 69.0 , 11.75 , 0.03 70.0 , 11.75 , 0.04 71.0 , 11.75 , 0.05 72.0 , 11.75 , 0.07 73.0 , 11.75 , 0.08 74.0 , 11.75 , 0.10 75.0 , 11.75 , 0.12 76.0 , 11.75 , 0.14 77.0 , 11.75 , 0.16 78.0 , 11.75 , 0.19 79.0 , 11.74 , 0.21 80.0 , 11.74 , 0.24 81.0 , 11.74 , 0.27 82.0 , 11.73 , 0.30 83.0 , 11.73 , 0.33 84.0 , 11.72 , 0.37 85.0 , 11.71 , 0.40 86.0 , 11.71 , 0.44 87.0 , 11.70 , 0.48 88.0 , 11.68 , 0.52 89.0 , 11.67 , 0.57 90.0 , 11.65 , 0.61 91.0 , 11.63 , 0.66 92.0 , 11.61 , 0.71 93.0 , 11.58 , 0.77 94.0 , 11.55 , 0.82 95.0 , 11.51 , 0.88 96.0 , 11.47 , 0.94 97.0 , 11.43 , 1.00 98.0 , 11.38 , 1.07 99.0 , 11.33 , 1.13 100.0 , 11.26 , 1.21 101.0 , 11.19 , 1.28 102.0 , 11.12 , 1.36 103.0 , 11.03 , 1.43 104.0 , 10.94 , 1.52 105.0 , 10.83 , 1.60 106.0 , 10.72 , 1.69 107.0 , 10.59 , 1.79 108.0 , 10.45 , 1.89 109.0 , 10.29 , 1.99 110.0 , 10.12 , 2.10 111.0 , 9.94 , 2.21 112.0 , 9.73 , 2.32 113.0 , 9.50 , 2.45 114.0 , 9.25 , 2.58 115.0 , 8.97 , 2.71 116.0 , 8.66 , 2.85 117.0 , 8.32 , 3.01 118.0 , 7.94 , 3.17 119.0 , 7.51 , 3.34 120.0 , 7.03 , 3.52 121.0 , 6.48 , 3.72 122.0 , 5.84 , 3.94 123.0 , 5.07 , 4.17 124.0 , 4.13 , 4.44 125.0 , 2.84 , 4.74 126.0 , 0.00 , 5.10
for a 10’6 noserider, i’d so something more like 19" nose, 23.5wide > point, a 16" tail, and a 7" squash -steve Here are the “Steve” numbers. My opinion, it would be a wave magnet, but a hog. Not as useful in juice. Use the whole thing, or the nose if you want to eat breakfast up there. x , y , Rocker 0.0 , 0.00 , 3.90 0.0 , 3.50 , 3.90 0.5 , 3.93 , 3.81 1.0 , 4.29 , 3.72 2.0 , 4.87 , 3.55 3.0 , 5.35 , 3.39 4.0 , 5.76 , 3.23 5.0 , 6.13 , 3.09 6.0 , 6.47 , 2.95 7.0 , 6.77 , 2.82 8.0 , 7.05 , 2.69 9.0 , 7.31 , 2.57 10.0 , 7.56 , 2.45 11.0 , 7.78 , 2.34 12.0 , 8.00 , 2.23 13.0 , 8.20 , 2.13 14.0 , 8.40 , 2.03 15.0 , 8.58 , 1.94 16.0 , 8.75 , 1.84 17.0 , 8.91 , 1.75 18.0 , 9.07 , 1.67 19.0 , 9.22 , 1.59 20.0 , 9.36 , 1.51 21.0 , 9.50 , 1.43 22.0 , 9.63 , 1.35 23.0 , 9.75 , 1.28 24.0 , 9.87 , 1.21 25.0 , 9.98 , 1.15 26.0 , 10.09 , 1.08 27.0 , 10.19 , 1.02 28.0 , 10.29 , 0.96 29.0 , 10.39 , 0.90 30.0 , 10.48 , 0.84 31.0 , 10.56 , 0.79 32.0 , 10.64 , 0.74 33.0 , 10.72 , 0.69 34.0 , 10.80 , 0.64 35.0 , 10.87 , 0.60 36.0 , 10.93 , 0.55 37.0 , 11.00 , 0.51 38.0 , 11.06 , 0.47 39.0 , 11.12 , 0.43 40.0 , 11.17 , 0.40 41.0 , 11.22 , 0.36 42.0 , 11.27 , 0.33 43.0 , 11.32 , 0.30 44.0 , 11.36 , 0.27 45.0 , 11.40 , 0.24 46.0 , 11.44 , 0.21 47.0 , 11.47 , 0.19 48.0 , 11.51 , 0.16 49.0 , 11.54 , 0.14 50.0 , 11.57 , 0.12 51.0 , 11.59 , 0.10 52.0 , 11.61 , 0.09 53.0 , 11.64 , 0.07 54.0 , 11.66 , 0.06 55.0 , 11.67 , 0.04 56.0 , 11.69 , 0.03 57.0 , 11.70 , 0.02 58.0 , 11.71 , 0.02 59.0 , 11.72 , 0.01 60.0 , 11.73 , 0.00 61.0 , 11.74 , 0.00 62.0 , 11.74 , 0.00 63.0 , 11.75 , 0.00 64.0 , 11.75 , 0.00 65.0 , 11.75 , 0.00 66.0 , 11.75 , 0.01 67.0 , 11.75 , 0.02 68.0 , 11.75 , 0.02 69.0 , 11.75 , 0.03 70.0 , 11.75 , 0.04 71.0 , 11.75 , 0.05 72.0 , 11.75 , 0.07 73.0 , 11.75 , 0.08 74.0 , 11.75 , 0.10 75.0 , 11.75 , 0.12 76.0 , 11.75 , 0.14 77.0 , 11.75 , 0.16 78.0 , 11.75 , 0.19 79.0 , 11.75 , 0.21 80.0 , 11.75 , 0.24 81.0 , 11.74 , 0.27 82.0 , 11.74 , 0.30 83.0 , 11.74 , 0.33 84.0 , 11.73 , 0.37 85.0 , 11.73 , 0.40 86.0 , 11.72 , 0.44 87.0 , 11.71 , 0.48 88.0 , 11.71 , 0.52 89.0 , 11.69 , 0.57 90.0 , 11.68 , 0.61 91.0 , 11.67 , 0.66 92.0 , 11.65 , 0.71 93.0 , 11.63 , 0.77 94.0 , 11.60 , 0.82 95.0 , 11.58 , 0.88 96.0 , 11.55 , 0.94 97.0 , 11.51 , 1.00 98.0 , 11.47 , 1.07 99.0 , 11.42 , 1.13 100.0 , 11.37 , 1.21 101.0 , 11.31 , 1.28 102.0 , 11.24 , 1.36 103.0 , 11.17 , 1.43 104.0 , 11.08 , 1.52 105.0 , 10.99 , 1.60 106.0 , 10.89 , 1.69 107.0 , 10.77 , 1.79 108.0 , 10.64 , 1.89 109.0 , 10.50 , 1.99 110.0 , 10.34 , 2.10 111.0 , 10.16 , 2.21 112.0 , 9.96 , 2.32 113.0 , 9.74 , 2.45 114.0 , 9.50 , 2.58 115.0 , 9.23 , 2.71 116.0 , 8.93 , 2.85 117.0 , 8.59 , 3.01 118.0 , 8.21 , 3.17 119.0 , 7.78 , 3.34 120.0 , 7.30 , 3.52 121.0 , 6.74 , 3.72 122.0 , 6.08 , 3.94 123.0 , 5.30 , 4.17 124.0 , 4.32 , 4.44 125.0 , 2.98 , 4.74 126.0 , 0.00 , 5.10
hey noodle, how does that program of yours work? im guessing the first column is inches, but what are the other 2?
hey noodle, how does that program of yours work? im guessing the first > column is inches, but what are the other 2? Instructions are below. Well… the measurements are in inches. Since inch measurements shorter than one foot break down in decimals, buy an engineer’s scale. For the outline, get a roll of wide paper. I use brown postage wrap. Tape the paper to a flat surface. Draw a straight line longer than the board, roughly centered down the length of the paper. This will be the center stringer line. Make a mark on one end. That mark will be zero, the board stern. Use a tape measure to measure up the line and make hash marks. Place marks at every “y” measurement within a foot or so of the board ends where the outline will curve a lot. You can mark every three or four inches at mid-board. Use a straight edge and a square to extend the hash marks to the rail lines. With your scale, measure from the stringer line, out each hash line, and place a mark where the rail will intersect it. By now you should be asking “Why didn’t I use crosshatch paper?” If you wanna blow the bucks, back up and use it. Draw a line around the rail outline. See how the outline looks. Adjust it as you like, then cut only the outline of one side of the board. Tape your template to the blank. Draw one rail, flip it and draw the other rail. Lets back up again. You just made an outline which measures the desired length around the rocker. I usually place the desired straight-measured end marks on the blank, then draw the nose and tail outlines from the ends to mid-board, shifting the template between draws. Use another long piece of paper the same way for a rocker template. Instead of cutting the template out of the paper, Get some spray on craft glue. Stick the paper to some 1/4" plywood, and cut an outside template along the board side of the line. Good luck.
Noodle, Did you develop some sort of spreadsheet to generate the numbers for the template? Can you explain how you set that program up? Thanks, Magoo
I’ve given awaw far too many program hints already. I still have dreams of going commercial. Right here on the bb there are internet programmers who have surpassed my abilities at communicating templates, but not at accurate shape definition. Sorry, now any programming info is too much.>>> Noodle, Did you develop some sort of spreadsheet to generate the numbers > for the template? Can you explain how you set that program up? Thanks, > Magoo
I’ve given awaw far too many program hints already. I still have dreams of > going commercial. Right here on the bb there are internet programmers who > have surpassed my abilities at communicating templates, but not at > accurate shape definition.>>> Sorry, now any programming info is too much. Noodle, No worries. I can appreciate your desire and your candor. I hope you are successful in your dreams to venture out commercially. You have helped me many times, so let take this post to formally thank you for your contributions to this site and the enhancing of my limited skills. Magoo
Noodle,>>> No worries. I can appreciate your desire and your candor. I hope you are > successful in your dreams to venture out commercially. You have helped me > many times, so let take this post to formally thank you for your > contributions to this site and the enhancing of my limited skills.>>> Magoo You’re welcome.
Noodle; can you please help me with some numbers for a 10’6"? I’m > thinking 18.5"nose,23.5 wide point at center,14.5" tail with > 5" squash. Thanks for your time and thank you swaylock for a great > site! Bruce Jones has some info on http://www.brucejones.com/longboar.htm regards, Håvard